The objective with this project was to design a new lifting aid connected to toilet chair.A questionnaire distributed at three homes for aged people indicated that there was an interest in a mechatronic lifting device.Since existing products have limited tilting functionality, the new design was chosen to introduce lifting by motorised tilting of the sitting platform. The mechanical construction was analyzed based on a maximum load caused by a person with weight 160 kg. Two linear actuators were used to control the tilting/lifting of the sit ?place, making standing-up easer.Finally, 28 persons tested the new lifting device and gave their impressions. Many appreciated the safe, stable lifting speed.

A clean and affordable energy source for cooking is deficient in developing countries. People rely on fuels that contribute to environmental, social and health problems.Biogas is an alternative energy source and an increased investment in small-scale biogas production can in several developing countries be found. Several projects have started to use the technology in developing countries because of the benefits with biogas. Some cases in the establishment of biogas plants have succeeded and some have not. The study is a literature review supplemented by two field studies.

The basis of the study lies with a newly patented gearbox by cardiologist and inventor Stig Lundbäck. Stig founded CorPower Ocean AB to further develop the gearbox to be used in a wave energy device. The purpose of this project is to develop a concept of a lifting system with CorPower Oceans gearbox that is more energy efficient than a hydraulic lifting system. The goal is to use technology from CorPower Oceans gearbox inversely to perform heavy lifting as an alternative to hydraulics. The project is limited to applying the gearbox and gear rack on a forklift with a lifting capacity of ten tons.The main tool in this project will be the product development process Systems Engineering where only the most relevant parts will be used to develop a concept.

There have been, in some rare cases, difficulties with clamping of inserts with U-holesin their tool holder. According to the complaints, the inserts could not be properlyclamped or could fracture when clamped. A study has shown that variations inclamping behaviour are mainly depending by the position of the screw hole in the toolholder and the centering of the screw hole in the insert.The focus of this project has been the centering of screw hole in insert. It has beenshown that the screw holes are not always enough centered in the insert. Theproblem may occur after a certain step in the production, i.e.

The project ?Investment proposal for grinding station for service work of screw feeders? has been performed during the spring semester 2014 for the course Bachelor?s thesis for degree of  Bachelor of science in machine engineering at Karlstad?s University. The project has been performed in cooperation with Fiber Workshop which is a service department in the company Valmet AB. Valmet AB is a company that develops and manufacture soft paper tissue machines. The screw feeder is a part that is used to feed, and squeeze out the water out of woodchips.

The purpose with this thesis is to get a compilation of all the critical bolted joints of all enginesproduced at LV Motors. ABB LV Motors produces induction engines with seven shaft heights. Eachengine size exists several variants of components ex. standard shield and flange shield. Depending onwhich components the engine is equipped with arises various types of strains in the engine's parts,certain assembly ways are more favourable than other.The most critical parts in the engine from a mechanical point of view are the screw units betweenshield/stator, feet/stator and bearing cover/shield.

In this thesis tests has been performed on the pull strength of screws glued into glulam beams.The experiment is based on the already approved method whereby the diameter of the drilled holes is the same as the screw outer diameter of 1 mm or bigger. The screws strength class shall not be less than 4.6 (EN ISO 898-1:1999, 1999).The difference in the experiments that were performed where that the drilled diameter were 1 mm smaller than the outer diameter of the screw so that the screw thread was worked into the wood.In the tests the gluing where made on M8 glulam beams. The screws where drilled at and angel of 90°tangental to the fiber direction with a diameter of 7 mm. The gluing of the screws where made in three different depths and where later exposed to pulling forces. The results showed both pulling breaks and screw breaks when they reached their maximum capacity.

Detta examensarbete har genomförts i samarbete med Svero Lifting. Företaget säljer och utvecklar lyftanordningar. Svero Lifting arbetar idag med att reducera vikten på företagets komponenter genom ett materialbyte och har påbörjat utveckling av en ny lyftanordning, en blockvagn och ett snabblyftblock. Svero Lifting vill fortsätta utveckla företagets lyftanordning så att komponenterna i lyftanordningen passar varandra och utmärker sig på marknaden. Idag har Svero Lifting inga CAD-modeller eller ritningar på företagets produkter.Huvudsyftet med examensarbetet är att skapa en ny design av ett snabblyftblock.

The work thesis was performed at Assalub a company which is situated in Åtvidaberg. The company works with developing, manufacturing and marketing equipment for handling of lubricants for light and heavier industry. The work thesis it is based on a inquiry Assalub got from MacGregor which is a company within cargo solution, from port to offshore system.For unloading grain and other material from the ship cargo it is used combined inlet feeder and screw conveyor, there the inlet feeder is drilling down through the cargo and feed the screw conveyer with material to further destination. At the bottom of the screw conveyer and the inlet feeder there is a bearing that keep the parts together. However the lubrication of the bearing must be made manually.

Stump wood was used between 1850 and 1950 for production of tar and as firewood. In the 1950s the use decreased because of the introduction of the cheap fossil oil. In the 1970s stump wood became an interesting issue again as a raw material for the pulp industry. Stump lifting has today become a possible source for bioenergy. The objectives with this study were to investigate the productivity of stump lifting and stump extraction, and to analyse the economy.

This Master Thesis has been carried out in cooperation with Ursus Medical AB (URSUS) which markets, assembles and sells the Rotex Screw Needle Biopsy Instrument ®. The instrument is delivered with an instrument holder. Customers had expressed dissatisfaction over that they needed to use two hands during a biopsy procedure, which resulted in a project to develop a new instrument holder.The project aim was to create concepts for how the new instrument holder should be designed, with focus on the mechanics. The new instrument holder would build on the existing basic principle that the screw needle and the cannula were screwed into the tissue. The thesis work would result in a technical solution and a functional prototype of the chosen concept.To achieve this, a generic product development processes were used and began with a comprehensive literature review.

The Master Thesis work this report is based upon has been conducted in cooperation with Svea Teknik AB. Svea Teknik is a consultant firm which is developing parts of a tunnel boring machine on behalf of Atlas Copco. The machine is being developed to mechanically excavate hard rock by fixating itself in the tunnel and then press a large rotating cutter-wheel equipped with disc-cutters against the tunnel wall. The disc-cutters are the tools that are in direct contact with the hard rock and are therefore exposed to extensive wear and needs to be replaced on a regular basis.The purpose of this Master Thesis has been to develop a service equipment that will enable time effective and safe changes of disc-cutters. The disc-cutters have a diameter of 17 inches and weigh about 130 kg.

This report reflects an examination work performed for Getrag All Wheel Drive AB during the spring of 2005. Among the companies range of products there exists some concern regarding the amount of clamping force and friction on bolted joints caused by the assembly torque.The aim of this project has been to determine if there is a simple way in which to identify and then practically apply testing methods for clamping force and friction through utilization of existing testing equipment.Three separate methods of clamping force and friction determination have been tested in rear drive unit, RDU, at a 30 Nm assembly torque. A fourth and final method, screw elongation with ultrasound, has been used as reference. The methods are:?Torque-Tension test.?Screw elongation with micrometer.?Joint stiffness test.?Screw elongation with ultra sound for reference.The results from tests can be viewed in table below.MethodTorque-TensionMicrometerCs=318 kN/mm Assembled with torque wrenchMicrometerCs=318 kN/mm Assembled on lineUltra-soundCS=311 kN/mm Ultra- soundCS=318 kN/mm Joint stiffnessTheoreticalClamping force-21,8 kN17,6 kN17,3 kN17,6 kN17,1 kN17,3 kNFriction-0,110,1470,1530,1470,1520,149.

The thesis is an examination of the methods that are appropriate and long-term choice to obtain clamping force and secure screw joints in production. The employer, Scania CV AB, transmission manufactures axle gears to all trucks produced in Södertälje. One of the most common assembly elements is screw joints, where the clamping force is essential to achieve a secure joint. Current methods to secure the joint is due much of the friction effect and is an indirect method to measure the clamping force. The clampforce accuracy becomes more widely with torque angle control.

In this study, the pre-tension force in an insert screw connection are examined in order to establish a greater understanding of the system and to facilitate the process of making new metal cutting tools. Certain especially significant design variables such as the offset, the length of the contact thread and the shank length above the threaded hole, are selected to be closely examined. A comparison of the influence on the pre-tension force between threaded holes made with a worn, versus new, threading tool is also involved in the experiment. The study is limited to handling the screw sizes M2,5 and M3,5. The results show that a regression model, with good approximation, can be fitted to the measured values.